etm-powersync-plugins-modbus/sunspec/froniusrules.h

// SPDX-License-Identifier: GPL-3.0-or-later

/* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*
* Copyright (C) 2026, ETM-PowerSync
*
* This file is part of nymea.
*
* nymea is free software: you can redistribute it and/or modify it under the
* terms of the GNU General Public License as published by the Free Software
* Foundation, either version 3 of the License, or (at your option) any later
* version.
*
* nymea is distributed in the hope that it will be useful, but WITHOUT ANY
* WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR
* A PARTICULAR PURPOSE. See the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License along with
* nymea. If not, see <https://www.gnu.org/licenses/>.
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */

#ifndef FRONIUSRULES_H
#define FRONIUSRULES_H

#include <QList>
#include <QString>
#include <QStringList>

#include <sunspecdatapoint.h>

#include "sunspecstoragelogic.h"

/* Vendor specific rules for Fronius GEN24 inverters.
 *
 * Everything here is a pure decision: no Modbus, no thing, no timer. The
 * plugin asks these functions what to do; the answers are what the unit tests
 * pin down. See specs/fronius-sunspec.md.
 */
namespace FroniusRules {

/* Polling. The manufacturer's support recommends staying above seven seconds
 * for third party applications. Below that, communication load can push the
 * inverter offline towards the manufacturer's portal, and recovery needs an
 * AC+DC power cycle on site. This floor is a guard in the code, not a
 * configurable default. */
const int MinimumUpdateIntervalSeconds = 7;
const int DefaultUpdateIntervalSeconds = 10;
const int DefaultTimeoutMilliSeconds = 2000;
const int DefaultNumberOfRetries = 3;

/* Revert timer armed with every setpoint, so that a setpoint left behind by a
 * stopped or crashed HEMS expires instead of holding the battery forever.
 *
 * WORKING HYPOTHESIS: the timer semantics are documented in the manual's
 * general chapter and illustrated on model 123, not on model 124. This must be
 * verified experimentally on model 124 before being frozen. If it does not
 * hold, fall back to 0 plus an application level watchdog in the HEMS. */
const int DefaultRevertTimeSeconds = 300;

/* Default unit IDs. The inverter is fixed at 1 over TCP; the meter defaults to
 * 200, with 201, 202... for secondary meters. 0 means "no meter on this
 * connection". */
const int InverterSlaveId = 1;
const int DefaultMeterSlaveId = 200;
const int MaximumSlaveId = 247;

/* Whether a second SunSpecConnection should be opened for the Smart Meter, and
 * why not when it should not. The caller logs the reason; keeping it out of
 * this function is what makes the decision testable without nymea. */
enum MeterConnectionDecision {
    MeterConnectionCreate,
    /* 0 is the documented way of saying "no meter behind this inverter". */
    MeterConnectionDisabled,
    /* A second socket on the unit ID already served by the inverter would
     * rediscover the very same models and duplicate every child thing. */
    MeterConnectionCollidesWithInverter,
    MeterConnectionInvalidSlaveId
};

MeterConnectionDecision decideMeterConnection(int meterSlaveId, int inverterSlaveId);

bool matchesManufacturer(const QStringList &manufacturers);

/* Sign to apply to the raw SunSpec meter power registers (W, WphA...) to get
 * the nymea smartmeter convention, where positive is import and negative is
 * export.
 *
 * The Fronius Smart Meter already reports in that convention: negative W is
 * feed-in. The generic path negates, so on a Fronius the surplus came out with
 * the wrong sign and the arbiter refused to run loads while the site was
 * exporting.
 *
 * Established on hardware, not from the manufacturer's documentation. On a
 * Primo GEN24 3.0, a *single phase* inverter feeding phase A only, the plugin
 * reported phase A at +1003 W (import) while phases B and C read -33 W and
 * -262 W (export). Exporting on two phases carrying no source is impossible.
 * With the sign flipped the balance closes exactly: production 1190 W = phase A
 * load 187 W + phase A export 1003 W, B and C import 294 W, so the house draws
 * 481 W and the site exports 709 W against 708 W measured. The meter's own
 * energy counters agree: over the same window its import counter stayed at
 * zero while its export counter advanced.
 *
 * Only the instantaneous power is affected. The energy counters map correctly
 * already and must not be swapped.
 *
 * The generic default is left untouched: other vendors keep the negation. */
double meterPowerSign(bool froniusMeter);

/* Whether a model 124 block is backed by a physically installed battery.
 *
 * A hybrid GEN24 publishes model 124 whether or not a battery is wired to it,
 * so the presence of the model proves nothing. Creating a storage child anyway
 * gives the customer a phantom battery and a permanent batteryCritical alarm:
 * observed on hardware, a GEN24 with no battery reported ChaSt = Off and a
 * state of charge of 0, and nymea's own energy engine then logged "There is no
 * energy storage available to consider" while the child stayed visible.
 *
 * The discriminator is deliberately a *physical* quantity. The state of charge
 * is refused because 0% cannot be told apart from a real but empty battery, and
 * the setpoint registers (WChaMax and friends) are refused because they keep
 * their defaults with no battery attached.
 *
 * INFÉRÉ: an installed battery carries a DC voltage at rest, so InBatV or
 * StorAval is expected to be strictly positive whenever one is present, and
 * both zero when none is. The absent side matches what the battery-less GEN24
 * showed and is reproduced on the simulator. The present side could NOT be
 * confirmed: no GEN24 with a battery was reachable. Confirm InBatV/StorAval on
 * a GEN24 with a battery before this ships. See DIVERGENCES.md. */
bool hasBattery(double batteryVoltage, double availableCharge);

/* Word order of the float32 points, measured on hardware.
 *
 * This used to read "INFERRED: not documented by the manufacturer, so the
 * SunSpec default is assumed. To be confirmed on the bench, then on hardware."
 * It has now been confirmed, and the assumption was wrong: what was assumed to
 * be "the SunSpec default" was in fact libnymea-sunspec's own default, which is
 * the opposite of the specification.
 *
 * A float32 spans two registers. SunSpec puts the high word first.
 * SunSpecDataPoint::convertToUInt32 reads registers.at(0) then .at(1) for
 * ByteOrderBigEndian, and the reverse for ByteOrderLittleEndian — and little
 * endian is the library's default. Keeping that default on a Fronius means
 * reading every float32 with its two words swapped.
 *
 * Measured 2026-08-07 on a Fronius Symo, read only:
 *   meter 213, unit 200 : Hz     = 4248 0000 -> 50.0000 big endian
 *                         PhVphA = 436a 8000 -> 234.5000
 *   inverter 113, unit 1: Hz     = 4247 fc48 -> 49.9964
 * Swapped, those same registers give 2.4e-41 and -4.2e+36: denormals, the
 * signature of a wrong interpretation rather than a measurement.
 *
 * What it costs to get this wrong is not a small offset. Reproduced on the
 * bench with the simulator emitting the hardware's order: a meter importing
 * 2.7 kW was reported as exporting 107 MW, and the arbiter switched every load
 * on. Correcting the SIGN of a denormal changes nothing, so meterPowerSign()
 * only becomes observable once this is right.
 *
 * The SolarEdge vendor already forces big endian on its own path; the generic
 * vendor keeps its user-settable parameter. Neither is affected. */
SunSpecDataPoint::ByteOrder byteOrder();

int clampUpdateInterval(int requestedSeconds);

/* Registers the GEN24 accepts and then ignores without raising a Modbus
 * exception. Writing them fails invisibly, so they are refused before being
 * put on the wire. */
bool isWriteForbidden(const QString &registerName);

enum BatteryMode {
    BatteryModeNormal,
    BatteryModeNoDischarge,
    BatteryModeNoCharge,
    BatteryModeFrozen,
    BatteryModeForceCharge,
    BatteryModeLimit
};

/* Sign convention of the manufacturer: negative is charging, positive is
 * discharging. chargeLimit and dischargeLimit are percentages of WChaMax and
 * are only used by the modes that need them. */
SunSpecStorageLogic::SetpointPlan planBatteryMode(BatteryMode mode,
                                                  double chargeLimit,
                                                  double dischargeLimit,
                                                  quint16 revertTime);

/* Model 160 repeating blocks are identified by their IDStr, never by their
 * index: on a three or four MPPT inverter the battery blocks are not in
 * position 3 and 4. */
enum BlockRole {
    BlockRolePvString,
    BlockRoleBatteryCharge,
    BlockRoleBatteryDischarge,
    BlockRoleUnknown
};

BlockRole classifyBlock(const QString &inputIdString);

struct ModuleReading {
    QString inputIdString;
    double dcPower;
};

/* Sum of the DC power of the PV string blocks. */
double pvPower(const QList<ModuleReading> &readings);

/* Discharge minus charge, so positive means discharging. DCW is a uint16 and
 * therefore always positive: the sign is carried by whichever block is active,
 * the inactive one reading zero. */
double batteryPower(const QList<ModuleReading> &readings);

}

#endif // FRONIUSRULES_H