etm-powersync-plugins-modbus/debian/changelog

etm-powersync-plugins-modbus (1.15.2+etm12) trixie; urgency=medium

  * v2c: the Trydan now declares phaseCount, and it is ENTERED at pairing.

    There is no phase register anywhere in the V2C Modbus map (0x0BC2-0x0BD5,
    0x177A-0x1783): the charger cannot tell whether it is wired single or three
    phase. The thing class did not declare phaseCount either, and the energy
    engine's fallback for a missing state is SILENT -- EvCharger::phaseCount()
    returns 1. On a three-phase Trydan that publishes a 1380 W floor instead of
    4140 (6 A x 230 V x 1 instead of x 3) and converts an allocated envelope
    into a current three times too high. The charger starts, at the wrong
    current, with nothing in any log to say so.

    That is the same defect family the energy plugin closed in 3g-2 -- a floor
    that is announced but is not the one governing the start -- reopened on the
    plugin side. Found the evening before the charger was due on the wall, by
    reading the class declaration rather than by running it.

    The value therefore comes from a SETTING (1 or 3, default 1), mirrored into
    the state the engine reads, and re-applied on settingChanged so a rewired
    charger can be corrected without recreating the thing. Default 1 matches the
    engine's own fallback, so an installation that never sets it behaves exactly
    as it did before this change.

    The state carries minValue 1 / maxValue 3: the nymea evcharger interface
    defines phaseCount with those bounds, and the plugin validator rejects the
    class without them. Conforming means the engine reads it through the
    interface, not through a plugin-specific convention.

  * v2c: still no sessionEnergy, deliberately. ChargeEnergy (0x0BC4) stays a
    diagnostic state -- see the plugin brief and evcc-io/evcc#28047. To be
    re-examined with the charger and a reference meter in hand.

 -- Patrick Schurig <etm.schurig@gmail.com>  Thu, 27 Aug 2026 15:20:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm11) trixie; urgency=medium

  * sunspec: stop warning about a missing battery channel on a machine that has
    simply not been read yet. libnymea-sunspec creates the repeating blocks of a
    model from initFinished, which fires during the FIRST block read, just
    before blockUpdated. On that first signal the blocks exist but carry no
    data: every IDStr is empty, nothing classifies, and hasBatteryBlocks()
    answered false about an inverter whose StCha/StDisCha blocks were there all
    along. Measured on the bench at 14:41:58: the warning fired once at startup
    on a storage whose currentPower then tracked the battery correctly through
    charge, discharge and rest.
    What that false positive cost is not noise. The README tells operations to
    grep that exact line first to tell a broken storage from an unmeasurable
    one; a line that appears at every healthy start tells them nothing. The two
    questions are now asked separately - blocksAreIdentified() before
    hasBatteryBlocks() - and the warning waits for the next refresh instead.

 -- Patrick Schurig <patrick@etm-schurig.eu>  Wed, 26 Aug 2026 16:10:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm10) trixie; urgency=medium

  * sunspec: make the SunSpec storage visible to the energy engine. The
    sunspecStorage thing class declared "battery" but not "energystorage", so
    the three consumers that filter by that interface never found it: nymea's
    power balance (currentPowerStorage, the figure the customer reads on their
    dashboard), the storage reserve of the EV surplus charging, and the reserve
    of the whole waterfall. Observed on the bench: GetPowerBalance answering
    currentPowerStorage 0 while the battery reported 50 % and "Holding". It was
    not at zero, it was invisible.
  * sunspec: publish currentPower and capacity on the storage, wired to
    registers rather than declared empty. Model 124 carries no power at all -
    WChaMax is a maximum, StorAval is in amp hours - so the instantaneous power
    is read from model 160, whose StCha and StDisCha blocks each carry an
    unsigned DCW with the inactive one at zero. currentPower is therefore
    DCW[StCha] - DCW[StDisCha], positive when charging, per the convention of
    libnymea/interfaces/energystorage.json. capacity comes from WHRtg of the
    nameplate model 120, and is left alone rather than zeroed when the
    nameplate does not implement it.
  * sunspec: the sign is measured, not deduced. Read only on the bench with the
    battery power driven over MQTT: a +2000 W charge order gives StCha 2000 W,
    StDisCha 0 W and ChaSt Charging; a -1500 W discharge order gives StCha 0 W,
    StDisCha 1500 W and ChaSt Discharging. The same run showed DCW_SF moving
    from -2 to -1 between idle and load, which is why the scale factor is never
    cached across a poll.
  * sunspec: warn once per thing when a storage has no power source - no model
    160 on its connection, or a model 160 with no StCha/StDisCha block. Such a
    thing now claims energystorage while reporting a flat zero, and a silent
    zero is what made the original defect expensive. See DIVERGENCES.md D-9.

 -- Patrick Schurig <patrick@etm-schurig.eu>  Wed, 26 Aug 2026 14:00:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm9) trixie; urgency=medium

  * sunspec: read Fronius float32 points big endian, the way the hardware
    emits them. byteOrder() returned ByteOrderLittleEndian on the grounds that
    "the SunSpec default is assumed"; that conflated the default of the
    specification with libnymea-sunspec's own, which is the opposite. Every
    float32 of the Fronius personality was therefore read with its two
    registers swapped. Measured on a Symo, read only: the model 213 meter on
    unit 200 serves Hz = 4248 0000, which is 50.0000 big endian and 2.3777e-41
    swapped. Reproduced on the bench: a meter importing 2.7 kW reported as
    exporting 107 MW, with the arbiter switching every load on, and the thing
    still reporting itself connected with no Modbus error. The meter sign fix
    only becomes observable once this is right. solarEdge already forces big
    endian and the generic vendor keeps its user parameter; neither changes.
  * sunspec: add tools/read-float-order.py, a read-only probe that decodes Hz
    and PhVphA both ways so the word order can be settled by measurement
    rather than assumption.

 -- Patrick Schurig <patrick@etm-schurig.eu>  Fri, 07 Aug 2026 07:00:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm8) trixie; urgency=medium

  * sunspec: ask the connection thing directly instead of resolving it by id.
    The battery presence gate went through isFroniusChild(), which looks the
    parent up in myThings(). During the initial setup the parent is not
    registered yet, the lookup answers false, the Fronius gate is bypassed and
    the phantom storage child is created after all. Caught on the bench, not
    by the unit suite, which covers the decision and not the wiring. See
    sunspec/DIVERGENCES.md D-7.

 -- Patrick Schurig <patrick@etm-schurig.eu>  Wed, 05 Aug 2026 19:20:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm7) trixie; urgency=medium

  * sunspec: correct the grid meter sign on Fronius. onMeterBlockUpdated()
    negated the power of every meter model regardless of vendor, but the
    Fronius Smart Meter already reports in the nymea convention, where a
    negative value is feed-in. The negation is now undone for meters sitting
    under a froniusConnection and only for those; generic and solarEdge keep
    their previous behaviour. Established on a Primo GEN24 3.0, whose single
    phase inverter gives the direction reference: the plugin reported the
    inverter's own phase as importing while the two phases carrying no source
    read as exporting. The arbiter concluded "insufficient surplus" and left
    the water heater and the heat pump off while the site was exporting.
    The energy counters were already correct and are left alone.
  * sunspec: stop creating a phantom battery on Fronius. A hybrid GEN24
    publishes model 124 whether or not a battery is wired to it, so a storage
    child was created unconditionally and sat on batteryCritical forever. The
    child is now created only when a physical quantity says a battery is
    there. The state of charge is deliberately not used: 0% cannot be told
    apart from a real but empty battery. See sunspec/DIVERGENCES.md D-6, the
    battery-present side is still inferred.

 -- Patrick Schurig <patrick@etm-schurig.eu>  Wed, 05 Aug 2026 15:58:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm6) trixie; urgency=medium

  * sunspec: package the vendored SunSpec plugin as nymea-plugin-sunspec-etm01.
    The plugin was added to the build by the vendoring commit but never
    packaged, so dh_missing found its .so in debian/tmp with nowhere to install
    it and aborted the whole source package: no binary package at all came out
    of this branch, not even for the four unrelated plugins.
  * sunspec: add the Fronius vendor. A GEN24 answers for the inverter on one
    unit ID and for its Smart Meter on another, behind the same host and port,
    so one froniusConnection thing now carries two SunSpecConnection objects.
    The meter connection is brought up only once the primary has finished
    discovering, and the parent connected state follows the primary alone.
  * sunspec: correct the storage setpoint chain - charge and discharge rates
    read back from InWRte/OutWRte instead of the read-only gradients, the rate
    range widened to -100..100 so forced charging can be expressed at all,
    enableDischarging reconciled from StorCtl_Mod, and the revert timer armed
    with every setpoint so one left behind by a stopped HEMS expires.
  * debian: add libnymea-sunspec-dev to Build-Depends. Upstream does not need
    it because it builds libnymea-sunspec from the same source tree; this
    repository vendors only the plugin and links against the installed library.
  * The new binary package conflicts with, replaces and provides
    nymea-plugin-sunspec: it ships the same plugin file and the same pluginId
    as the upstream package this repository already mirrors.

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Sun, 02 Aug 2026 12:05:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm5) trixie; urgency=medium

  * abbterra: decode the serial-number and firmware register fields as BCD, as
    specified by the ABB Modbus spec §5.1 (e.g. 0x49 = week 49, 0x22 = 22 kW),
    instead of as plain binary. The binary reading made deviceInfoFromValues()
    reject every real charger whose BCD production-week byte exceeded 0x35
    (e.g. week 46 = 0x46 = 70 > 53), failing setup with "The device does not
    match the ABB Terra AC Modbus register map", and mis-decoded the 11 kW/22 kW
    rated-power codes. Manual TCP add of the charger now completes.

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Fri, 03 Jul 2026 13:15:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm4) trixie; urgency=medium

  * abbterra: fix TCP manual setup never establishing the connection.
    setupTcpThing() wired all the connection signals but never called
    connectDevice(), so reachableChanged()/initializationFinished() never fired
    and the setup hung until timeout ("Thing setup failed"). Now the connection
    is started when the NetworkDeviceMonitor reports the device online.

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Fri, 03 Jul 2026 12:55:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm3) trixie; urgency=medium

  * abbterra: disable TCP auto-discovery (createMethods = "user" only) for the
    Terra AC Charger (TCP) thing class. Discovery blind-scans the LAN and blows
    up nymead with a SIGSEGV as soon as any Modbus device answers :502 with an
    exception response — the crash is in the generated reachability handler and
    cannot be fixed from the discovery code alone (two attempts failed). For the
    Waveshare RS485-gateway use case discovery can't determine the slave id
    anyway; the charger must be added manually (address + port + slaveId). This
    unblocks adding the charger and stops the crash loop. The underlying
    generated-code crash is tracked separately.

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Fri, 03 Jul 2026 12:40:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm2) trixie; urgency=medium

  * abbterra: fix nymead SIGSEGV during ABB Terra AC TCP discovery. On a
    reachability-check exception (e.g. any Modbus device on the LAN answering
    :502 with "illegal data address"), AbbTerraTcpDiscovery::cleanupConnection()
    tore the connection down synchronously from inside the connection's own
    QModbusReply "finished" handler, freeing the in-flight reply that the
    generated code still dereferences at abbterramodbustcpconnection.cpp:2062.
    The teardown is now deferred (Qt::QueuedConnection) and made idempotent.
  * abbterra: restore checkReachableRegister ("serialNumber"), required by the
    libnymea-modbus 1.15 connection-class generator.

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Fri, 03 Jul 2026 12:00:00 +0200

etm-powersync-plugins-modbus (1.15.2+etm1) trixie; urgency=medium

  * Build 1.15,2

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Tue, 24 Jun 2026 11:00:00 +0200

etm-powersync-plugins-modbus (1.15.0+etm5) trixie; urgency=medium

  * abbterra: fix RTU setup on slow radio links — trigger initialize() on
    master connectedChanged, not only on reachableChanged (which never fires
    within setup timeout over 433 MHz).

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Tue, 24 Jun 2026 10:00:00 +0200

etm-powersync-plugins-modbus (1.15.0+etm4) trixie; urgency=medium

  * Correction modbus registers.

 -- ETM-Schurig SARL <contact@etm-schurig.eu>  Fri, 13 Jun 2026 10:00:00 +0200